Produkty dla do silników (383)

Sanascreed Walkable screed based on hydraulic lime, silico-calcareous aggregates with a maximum grain size of 5 mm and light aggregates with pozzolanic activity, fiber-reinforced with polypropylene and glass microfibres, used for the construction, with the addition of water, of resistant screeds and substrates , in green building interventions and in the restoration of period and monumental buildings. Laying slabs and screeds based on hydraulic lime. Application surfaces should be clean, free of soiling, crumbling and non-adhering parts, dust, etc., conveniently saturated with water until they reach the condition "saturated with dry surface". Pour about 2/3 of the mixing water into the mixer. Gradually add Sanascreed and the water still required, continue to mix until a homogeneous, lump-free mixture of the desired consistency is obtained. Support the product at the reference height and float until a smooth and planar surface is obtained, preparing the joints beforehand where necessary. The mixing water indicatively necessary is equal to 18-20% by weight (4.5 -5 litres per bag 25 kg). Approximately 17 kg/m² of Sanascreed for every centimetre of thickness to be implemented (approximately 1700 kg per cubic metre). Bag 25 kg

Sanareg Non-film reactive liquid based on an alkylsilane emulsion dissolved in water to be used for the inhibition of saline efflorescence in the dehumidifying restoration of masonry, by spraying or applying with a brush with rigid bristles. Sanareg penetrates into the capillary pores of mineral substrates and reacts with the hydroxyl groups encountered in its path, forming an invisible water-repellent barrier that does not allow water to escape to the surface, leaving the transpiration to water vapor unaltered. Sanareg is an alkylsilane water emulsion, non-hazardous, non-toxic and VOC-free. The application of Sanareg does not alter the original wall breathability. Particularly indicated in combination with the cycle of natural dehumidifying plasters Untersana, Sanatigh and Sanastof. This also applies to Untersana, Caleosana and Sanastof. Non-film reactive liquid based on an alkylsilane emulsion dissolved in water to be used for the inhibition of saline efflorescence in the dehumidifying restoration of masonry, by spraying or applying with a brush with rigid bristles. Sanareg penetrates into the capillary pores of mineral substrates and reacts with the hydroxyl groups encountered in its path, forming an invisible water-repellent barrier that does not allow water to escape to the surface, leaving the transpiration to water vapor unaltered. Remove the soilings and saline manifestations by vigorous brushing; then eliminate any dust residue. Surfaces should be as dry as possible at the time of application. Apply Sanareg by spraying or with a long-bristled brush, proceeding from the bottom upwards. Remove any surface excess. When used as a preliminary treatment before a plastering cycle, apply the first coat of rendering immediately after applying Sanareg. Sanareg is water-based, which is why its effectiveness is not compromised even if the substrate is not perfectly dry at the time of application. From 0.10 to 0.20 kg of Sanareg for each square metre of surface to be treated, based on the porosity of the support. Plastic can 5 kg - Plastic can 25 kg

Sanafirm Adhesive, thixotropic, reinforced fibre compound, based on hydraulic lime, reinforced fibre, fast-curing, for fastening and anchorage, of wall bodies, structures, inserts, plates, frames, bars, sanitary, etc., in ecological building interventions, new buildings and in the restoration of vintage buildings and monuments. Sanafirm consists of hydraulic lime, botticino, quartz sands, kaolin, aluminates and natural fibres. It does not contain cement, resins, solvents and radioemissive elements. Fixing and anchoring, in wall bodies, plates, door and window frames, washbasins and sanitary ware in general, bars, clamps, connectors, and metal inserts etc. Application surfaces should be clean, free of soiling, crumbling and non-adhering parts, dust, etc., conveniently saturated with water until they reach the condition "saturated with dry surface". Pour about 2/3 of the mixing water into the mixer; gradually add Sanafirm and the water still required, continue to mix until a homogeneous lump-free mixture of the desired consistency is obtained. Apply with brick trowel or filling knife. The mixing water indicatively necessary is equal to 15-16% by weight (3.5 -4 litres per bag 25kg). Approximately 1.6 kg of Sanafirm for each cubic decimetre of volume to be filled. Bag 25 kg - Pallet: 50 x (Bag 25 kg)

Sanafast Sanafast is a specially formulated premix that, added during the mixing phase to our mortars (REPAR, GROUT, FLOOR, RINFOR lines) and to our natural hydraulic lime-based injection products (Sanafluens, Mikrosana), allows to accelerate the setting and hardening, with a much faster development of mechanical strength. Sanafast is formulated with a fast-setting binder and very fine mineral fillers, perfectly compatible with Portland cements, pozzolanic cements and natural hydraulic lime. Adaptation (acceleration) of the setting times of mortars and plasters, to be used when environmental and meteorological conditions would make them too "slow" compared to the requirements of use: for example in the winter period when temperatures are low. Careful dry premixing of Sanafast with the product for which an acceleration of setting and hardening times is always recommended. Sanafast can be mixed in any proportion with any hydraulic binder. Bag 25 kg - Pail 10 kg

Sanafarbe I Natural, protective, decorative, breathable, pigmented, non-toxic putty coat, naturally mildewcide, based on hardened lime putty and botticino marble dust, for indoors and outdoors. Formulation prepared according to the traditional recipes, for use in ecological building interventions and in the restoration of vintage buildings and monuments. Product based on lime putty and natural pigments. SANAFARBE putty coat has a high breathability, a remarkable mildewcide and antibacterial capacity. It has no solvents, thinners, harmful substances in general. Embodiment of putty coat finishing, protective and decorative, internal and external masonry building, in ecological building interventions and in the restoration of vintage buildings and monuments. The application supports will be free from fouling, powder, non-adhering parts, etc.; existing paints (washable, organic, solvent based etc.) must be removed. Spread Sanafarbe I, into two coats: the first, by simple deposition, with steel trowel, the second for laying and finishing, with sponge float. The application of the second coat must be carried out, when the first coat starts to dry, in one of two conditions suggested: with dry trowel, for smooth surfaces, with moistened trowel, for antique-effect surfaces. SANAFARBE-I is dry to the touch after 4 hours, it can be overcoated after 2-5 hours, while it will be dry in-depth after 16-32 hours. Indicative consumption depending on the different particle sizes of Sanafarbe I available: 1 mm GRAIN: approximately 1.6 -1.8 kg/m²; 1.2 mm GRAIN: approximately 1.8 -2.0 kg/m²; 2 mm GRAIN: approximately 2.4 -2.8 kg/m²; 2.2 mm GRAIN: approximately 2.6 -3.0 kg/m². The indicated yields refer to smooth supports and are for guidance only. Actual consumption must be identified with a suitable practical test. Pail 5 kg - Pail 25 kg

Ringseal L19 RINGSEAL L­19 is a rectangular gasket with a central hole of 19 mm x 2 mm, made with a special hydro-expansive rubber that reacts in contact with water by increasing its initial volume. RINGSEAL L­19, used in combination with a normal metal spacer for moulds made of wood ("blade"), hermetically seals the discontinuities which could easily settle in the concrete due to the presence of the spacers; these discontinuities could in many cases pass from one side of the masonry to the other, and which then might seriously compromise the watertightness of the masonry itself. The hydro-expansive capacity of RINGSEAL L­19 has been tested in the laboratory with three different types of water: demineralised water, salt water and water with strongly basic Ph (to simulate the conditions in contact with the concrete). The expansion tests showed a change in volume ranging from a minimum of about 200% (three times the initial volume) in the case of salt water to a maximum in excess of 900% in the case of demineralised water. In the standard version, the seal RINGSEAL L­19 is sized for the usual measures of the blade caisson spacers, normally used in the construction industry: in this case with a width of about 20 mm, in the version straight/flat or "twisted" (designed to minimise the propensity to form deformities during the pouring of the concrete in the formwork). Subterranean construction of concrete by formwork in wood, where the wall is in direct contact with the ground and where there is the presence of waterproofing layers external to the masonry itself: basements, cellars, underground garages, underground environments and basements, etc. Place the hydro-expansive seal RINGSEAL L­19 with the appropriate dilating pliers in central position with respect to the length of the blade caisson spacers (one seal for each spacer). Build the planned formwork using the metal spacer for wooden formworks thus prepared and proceed with the usual operations of casting the concrete. No. 1 Ringseal L19 gasket for each "blade" formwork spacer (average 6 - 8 pieces per square metre for wooden formworks of 2 x 0.5 metres). Small bag 200 unit

Repar Tix SFR High-performance, thixotropic, structural cementitious mortar, fiber-reinforced with a mix of metal microfibers (length = 6 mm, diameter = 0.22 mm) and alkaline-resistant synthetic microfibers, used for the restoration and thickening of reinforced concrete structures and in masonry, even in severe exposure environments (marine, industrial, cyclically dry and wet). Repar Tix SFR consists of special cements, silica fume, anti-shrinkage agents, specific additives and selected aggregates, high-performance in terms of adhesion, adherence, mechanical resistance, intrinsic watertightness, dimensional stability and overall hardness. Repar Tix SFR is added with a mix of amorphous metal fibres of 30 mm (≥0.9% by weight) and multifilament synthetic fibres of 6 mm (≥0.08% by weight). Restorations, repairs and consolidations, even of considerable thicknesses and dimensions, on reinforced concrete and masonry structures. Reinstatement and reconstruction of the concrete cover on heavily deteriorated reinforced concrete works, even in particularly demanding and heavily stressed environments (marine, industrial, purification plants, hydraulic pipes). Reliable and durable structural consolidation of road structures (bridges, viaducts, tunnels, etc.). Reinforcement hoods on vaulted wall structures. Reinforcements and seismic adjustments in combination with structural glass fiber meshes from the ARMAGLASS line, Armaglass Connector glass fiber connectors, helical bars in Helix Steel AISI 304 stainless steel. Application surfaces should be clean, free of soiling, crumbling and non-adhering parts, dust, etc., conveniently saturated with water until they reach the condition "saturated with dry surface". An adequate roughening of the surfaces by scarifying, sandblasting etc. is always necessary in order to obtain the maximum adhesion values to the substrate. The optimal values are obtained with high pressure hydro-scarification. Bare the irons undergoing disruptive oxidation or deeply oxidized, removing the rust of the exposed irons (by sandblasting or abrasive brushes). Pour about 2/3 of the mixing water into the mixer, add Repar Tix SFR and the remaining water; continue to mix until a homogeneous lump-free mixture is obtained. The mixing water should be about 20-22% of the weight of the bag. After mixing is completed wait a few minutes before applying. Place on site by rendering or using plastering /or shotcrete machines, use product quantities appropriate for the specific requirements of the construction site. Approximately 19 kg/m² of Repar Tix SFR for every centimetre of thickness to be implemented (approximately 1900 kg per cubic metre). Bag 25 kg - Pallet: 50 x (Bag 25 kg)

Protech Tunnel Tempera paint with high specific coverage, high dry residue and discrete water repellence, for painting signs and decorative interior surfaces generally relating to tunnels, galleries, subways, etc. Pure white: RAL 9010 Vermilion: RAL 2002. Painting vertical and decorative signs for tunnels, galleries and subways. The surfaces of application should be clean, free of any soiling, crumbling and non-adhering parts, or non-absorbent, dust, pre-existing paints, etc. Apply the specific fixative PROTECH FIX TUNNEL on the surfaces to be treated, using low pressure airless. Apply Protech Tunnel with airless pumps at low pressure, diluting it preliminarily with water in the recommended percentage of 30%-40% by weight of the product. Apply from 0.30 to 0.50 liters of Protech Tunnel per square metre of surface to be painted. Pail 15 l

Protech Rooftop Protective and waterproofing liquid coating, single-component, coloured, based on special elastomeric polymers in aqueous emulsion, suitable for the waterproof protection of flat roofs, pitched roofs, attics, walkable terraces, old bituminous coverings and external areas subject to atmospheric agents. The product is resistant to UV rays and water stagnation. It can be advantageously used as an elastomeric paint for the protection of concrete infrastructures and cementitious supports in general. -Quick and easy application, even on large surfaces Ready-to-use single-component, extremely elastic with good mechanical resistance -Exceptional resistance to atmospheric agents, both in mountain conditions and in marine or industrial environments -The elastic properties allow the creation of a protective coating that compensates for the expansion and micro-cracks of the supports subject to vibrations or settlements. -It protects the artefacts from carbonation and degradation caused by carbon dioxide and other acidic substances present in the atmosphere, while at the same time giving a pleasant aesthetic effect and greater durability. -Waterproofing of flat roofs, pitched roofs, floors, concrete and reinforced concrete slabs -Waterproofing and repair of old smooth or slated bituminous coverings -Waterproofing of roofs made of galvanized sheets, pre-painted sheets, PVC sheets, fiber cement sheets, wooden or brick floors -Elastic protection of concrete and cement infrastructures in general -Anti-carbonation protection for greater durability of the product -Creation of waterproof protective coatings without joints or fittings even on large external surfaces, which can occasionally be walked on for maintenance work -Applicable inside concrete pipes and prefabricated concrete elements for the elastic and waterproof protection of joints and male and female joints. The surfaces to be coated must be stable, clean and free of substances that can affect the adhesion of the waterproofing coating. Repair and restore any degraded or missing parts, appropriately leveling the bottom support. Check the adequacy of the slopes and rainwater collection and canalization systems. The application of the product must be carried out on a dry support. Check the absence of any rising humidity and/or negative pressures of water which could generate vapor tension between the support and the elastic waterproofing coating, favoring the formation of bubbles or detachment. Any structural joints must be waterproofed with suitable systems before installing the elastic waterproof covering. Before installing elastic waterproofing systems and coatings on horizontal surfaces, always check the residual humidity content. Check for the presence of residual humidity using the plastic sheet method according to the ASTM D 4263 standard: fix a heavy polyethylene sheet with a size of at least 45x45 cm to the support with adhesive tape. 24 hours after its installation, lift the sheet and check for signs of humidity. If testing with a carbide hygrometer, the moisture content of the substrate must be < 4%. As waterproofing ~ 2 kg/m2 per mm of thickness As an elastomeric protective paint 0.15-0.2 kg/m2 per coat (apply two coats). Can 5 kg - Can 20 kg

Protech Road Paint Protech Road Paint is a thick paint based on acrylic resins in aqueous emulsion for the protection and waterproofing of bituminous floors in urban and pedestrian areas. Protech Road Paint is ideal for surfaces in car parks, yards, cycle paths and sidewalks, it also increases the resistance of the floor to wear, UV rays and chemical aggression. Protech Road Paint avoids the migration of bituminous binders and the accumulation of heat due to sunlight and allows to: - Reduce the disintegration, breakage and swelling of the bituminous artefact. - Protect the paving in bituminous conglomerate from sudden changes in temperature. - Increase the durability of the work. - Improve the aesthetics of the flooring and reduce the environmental impact being able to choose from various colours. - Noticeably reduce bitumen odours. Protech Road Paint is formulated for the finishing and protection of manufactured products in bituminous conglomerate in urban and pedestrian areas such as yards, avenues and preferential lanes, sidewalks and cycle paths, sports facilities. Remove all traces of dust and traces of oils, greasy substances and incoherent parts. On a dry support, apply Protech Road Paint according to the methods described in the instructions for use. Protech Road Paint can be diluted with water in a percentage not exceeding 30%. The application on a dry and clean surface is done manually with a roller for a minimum of 2 coats until saturation depending on the porosity of the support. We do not recommend the application with temperatures below +10°C. Approximately 2.0 kg/m² of Protech Road Paint in two coats. Can 25 kg

Untersana With the addition of mixing water only, this single-component premix creates a breathable, dehumidifying rough coating, preparatory to the application of restorative, dehumidifying, thermal-insulating and anti-condensation plasters, specifically Intosana, Sanatigh, Sanawarme and Caleosana, being plasters designed specifically for the healthiness of new buildings, existing buildings, works on green buildings and in the restoration of historic and monumental buildings. Untersana is composed of hydraulic lime, botticino, kaolin, calcium caseinate, Vichy salt, tartaric acid and natural fibres. Does not contain cements, resins, solvents, thinners and radioemissive aggregates. Anchoring scratch coat (applied by "spraying" or "splashing") for the formation of an adhesive bridge for easy grip of subsequent plasters, dehumidifying, breathable, based on hydraulic lime. Application surfaces should be clean, free of soiling, crumbling and non-adhering parts, dust, etc., conveniently saturated with water until they reach the condition "saturated with dry surface". Pour about 2/3 of the mixing water into the mixer, add Untersana and the remaining water; continue to mix until a homogeneous lump-free mixture is obtained. The mixing water should be about 22-25% of the weight of the bag. After mixing is completed wait a few minutes before applying. "Spray" the product, with plastic fluid consistency, on the application supports, with plastering trowel and brick trowel or with plastering pump. Protect fresh surfaces from direct exposure to sunlight, from the rain and wind, cure the prolonged moist hardening. From 4 to 6 kg of Untersana per square metre of surface to be rendered. Bag 25 kg - Pallet: 50 x (Bag 25 kg)

Unisan A composite mortar that is fibre-reinforced, consolidating, dehumidifying, grey in colour and utilised for the structural restoration of crumbling old or monumental masonry. It contains no substances that are potentially harmful to masonry and is composed of NHL 3.5 natural hydraulic lime and hydraulic binders free from soluble salts, along with silicas with pozzolanic activity, selected siliceous-calcareous aggregates, specific shrinkage-reducing agents and resistant alkaline READYMESH fibres that confer high flex-traction whilst increasing the performance of the mortar’s fracture energy. In conjunction with ARMAGLASS STRUCTURA fibreglass mesh, it is ideal for the structural restoration of old walls or crumbling constructions. Construction of plasters and reinforced slabs in interventions of restoration, construction of plaster and dehumidifying coatings with high performance, bedding of bricks and modular elements. The surfaces should be clean and free of any soiling, crumbling and non-adhering parts, dust, etc., conveniently saturated with water until they reach the condition of "saturated dry surface". In the case of structural reinforcing slabs, you will need to proceed with applying an appropriate reinforcing electrowelded mesh, to be fixed with PROFIX, Grout Micro-J, Repar Tix G2 or Syntech IC 55. Pour about 2/3 of the mixing water into the mixer, add Unisan and the remaining water; continue to mix until a homogeneous lump-free mixture is obtained. The mixing water should be about 12-14% of the weight of the bag. After mixing is completed wait a few minutes before applying. Apply the product by plastering trowel and brick trowel, or preferably with plastering machine (type PFT model G4). Do not apply in case of direct exposure to sunlight or excessive ventilation. Cure the protection and the prolonged moist hardening, of exposed surfaces. Approximately 15 kg/m² of Unisan for every centimetre of thickness to be implemented (approximately 1500 kg per cubic metre). Bag 25 kg - Pallet: 50 x (Bag 25 kg)

Unikoll A certified single-component cementitious adhesive with a base of hydraulic binders free from harmful additives, containing starch-derived adhesion promoters, selected siliceous and calcareous sands, reactive fillers with high pozzolanic activity and cellulosic thickeners for bonding tiles, ceramics, stoneware and natural and/or reconstructed stones on horizontal and vertical surfaces, for use both internally and externally. Cannot be used for plaster or anhydride substrates nor for substrates subject to movement or bearing a protective film. Bonding of tiles, ceramics, stoneware, natural and/or reconstructed stones, etc. on horizontal and vertical surfaces, internal and external. Regularisation finishings. Modular element bonding and smoothing for insulating cladding: polystyrene sheets, wood panels- magnesium panels, wood-cement, etc. Do not use for: - Substrates in gypsum or anhydrite - Substrates subject to movements - Substrates with protective films or coatings. The surfaces of application have to be properly cured, conveniently roughened, clean, free of any soiling whatever its nature, crumbling and non-adhering parts, dust etc. Any traces of oils, greases, release agents, waxes, paints, etc., as well as any anti-adhesive substance, should be preliminarily removed. For each 25 kg bag of Unikoll, add 6-6.3 litres of clean water and mix thoroughly, with a mechanical stirrer, until a homogeneous lump-free mixture is obtained. After waiting a few minutes, stir and spread the adhesive with a toothed adhesive spreader. The products (tiles or other coatings) should be applied with a slight pressurised movement for the entire surface to be in perfect contact with the adhesive. Any adjustment must be made within 10-12 minutes of laying. For applications outdoors, apply a continuous layer of adhesive also on the back of the item. Use from 3 to 5 kg/m² of Unikoll depending on the type of support and the type of material to be bonded. Bag 25 kg - Pallet: 50 x (Bag 25 kg)

Syntech Primer EP-W Syntech Primer EP-W is a solvent-free two-component epoxy resin to be used as a bonding primer for applying all epoxy cycles on concrete surfaces and concrete conglomerates in general. Syntech Primer EP-W is formulated to achieve an elevated impregnation, consolidation and adhesion effect of the substrate. It can also be used on wet surfaces. Syntech Primer EP-W even penetrates deep into compact surfaces, effectively consolidating the support. It also has a great resistance to water and aggressive solutions whilst allowing water vapour to pass through. Promotes adhesion for epoxy coatings as well as for porous and deteriorated substrates, along with acting as a cement and concrete consolidation agent. The support on which the epoxy, polyurethane or methacrylic system is to be laid must be suitable for withstanding the stresses resulting from the intended use, such as static or dynamic loads, impacts, thermo-hygrometric expansion, vibrations etc. As regards the characteristics of the substrate (maximum humidity, cohesion, strength class, flatness, etc.) and the preparation of the surface that will accommodate the resin system, we recommend the requirements set out in chapter 5 of the UNI 10966 standard ("RESIN SYSTEMS FOR SURFACES HORIZONTAL AND VERTICAL - INSTRUCTIONS FOR DESIGN AND APPLICATION "). In any case, carefully clean and degrease the surfaces, removing any kind of dirt, paint residues or incoherent parts. The humidity of the support must be <= 4%. Evaluate the most convenient type of mechanical preparation (shot peening, sandblasting, hydro-washing, etc.). The surfaces must also be free from discontinuity, and possibly leveled and regularized with products from the FLOOR line or the REPAR line or grouted with Syntech AS 21. In the event of the presence (even suspected) of humidity deriving from capillary rising from the substrate, it is recommended to apply the Syntech Pavidamp epoxy resin for "wet bottoms" beforehand. Tiled floors, or floors covered with pre-existing resin, must be subjected to mechanical roughening carried out with shot blasting, milling, bush hammering, etc., until the total elimination of the waterproof crust and the opacification of the surfaces. Remove dust after abrasion. Mix the two components, each in its own container, before combining. Pour component B into component A and mix for 3 to 5 minutes with a low-speed mixing drill to achieve the complete homogenisation of the mixture. The protective coating can be applied once the Syntech Primer EP-W is completely dry. Use 150 to 200 grams per square metre per coat, depending on the porosity and unevenness of the support. Can 10 kg [A] - Can 5 kg [A] - Can 5 kg [B] - Can 2.5 kg [B] - Kit: 1 Can 10 kg [A] + 1 Can 5 kg [B] - Kit: 1 Can 5 kg [A] + 1 Can 2.5 kg [B]

Syntech Flexipur Syntech Flexipur is a two-component aliphatic elastic polyurethane resin in the solvent phase, with excellent characteristics of chemical resistance and flexibility, ideal for the protective finish of both new and restored reinforced concrete structures. Syntech Flexipur is applied by roller or spray (airless) creating a film-forming coating with high protective capacity and resistance to cracking (crack bridging ability). Syntech Flexipur is ideal for creating the surface protection of both new and existing reinforced concrete structures; The final protective treatment of coatings for commercial activities, offices, hospitals and public environments in general; It can be used for UV protection of solvent-free polymeric elastic sheaths. Mix the two components in their respective packaging. Then pour component B into the container of component A. Mix everything for 3-4 minutes using a low-speed mechanical stirrer until a homogeneous and lump-free mixture is obtained. Mix the dough again for a few minutes to mix the mixture. Apply the product within 60 minutes. Syntech Flexipur can be applied by roller or spray (airless). With manual roller application it is advisable to foresee 2 successive coats, spaced out by a minimum time of 5 hours (20 ° C and 65% R.H.). In the case of spray application (airless) it is possible to apply the recommended thickness of 200-300 dry microns in a single coat. The product must be applied at temperatures between +10 and + 35 ° C; optimal density and workability are obtained at a temperature of + 20 ° C. Approximately 80-120 g / m2 of Syntech Flexipur for each coat (apply two coats). Can 6.7 kg [A] - Can 3.3 kg [B] - Kit: 1 Can 6.7 kg [A] + 1 Can 3.3 kg [B]

Sealpvc SF 240 Bulb The Sealpvc SF 240 Bulb waterstop is a waterproofing PVC profile that is not hydro-expansive, having a thickness of 24 centimetres and equipped with a central and highly elastic bulb. It is used in dynamic joints for horizontal casting (slabs), in concrete structures, resting on the substrate beneath the reinforcement, in a position central to the casting. Given its particular composition, it can be cut with a sharp blade (cutter) and welded with simple heat welding tools, thus making it easier to create connections in the course of work. Waterproofing of dinamic construction joints between: raft foundation and the elevation wall, between two raft foundations, between two elevation walls, between the wall and floor, resting on foundations under the shoring. Bind with iron wire the side flaps of the waterstop to the steel plates provided, in order to position it and secure it in a central position with respect to the casting to be made. Proceed with the casting operations, ensuring it does not bend nor move from the seat identified. 1 m/m: Use Sealpvc SF 240 Bulb welding the two edges of different belts head to head using a leister (manual hot air welder). Roll 25 m

Sanaxil P - Therm Mineral paint for interiors and exteriors with potassium silicates, with strong adhesion characteristics on porous substrates, both for mineral combinations and for chemical bonds. It combines anti-condensation and insulating characteristics (thanks to the presence of 3M Glass Bubble hollow glass microspheres in the formulation) with strong resistance to mold and microorganisms (thanks to the natural alkaline pH of potassium silicate) and excellent hiding power (class 1 according to EN 13300 for a yield of 6/7 m2 / l). Sanaxil P - Therm due to its mineral nature, revolutionizes the concept of adhesion to the substrate, penetrating deeply into the porosity of the wall and then reacting with its components and forming a unique and indissoluble silicate bond. The product does not form a film, thus avoiding detachment and flaking phenomena and, while ensuring excellent water repellency, ensures high values of permeability to water vapor thanks to its porous and microcrystalline structure, perfectly compatible with mortars, plasters and all other common elements of the body masonry. Physical-mechanical performance and durability are coupled with a vast choice of colors that cannot be altered over time; characteristics which, combined with the ease and practicality of application, make the product extremely versatile and adaptable to any project requirement. Protective, restorative coatings with strong antibacterial and anti-mold characteristics, based on stabilized potassium silicates, for vertical and horizontal surfaces. Heat reflective paint that helps to increase the thermal efficiency of the building. SUPPORTS ALREADY PAINTED WITH SILICATE PAINT Remove any stains and proceed with painting with the silicate paint. (it is always recommended to apply a coat of silicate impregnating agent). NEW SUPPORTS Apply a coat of potassium silicate fixative diluted from 30/40% with water depending on the absorption of the support. OLD SUPPORTS On old supports, remove the old paint by brushing, fill in any holes or imperfections in the wall with a suitable filler, proceed with fixing with potassium silicate impregnating agent diluted 30/40% with water depending on the absorption of the support. DILUTION (in volume with potable water) 1st COAT BRUSH: 15% one coat crossed or two coats 12-24 hours apart ROLLER: 10% SPRAY (with specific equipment): 15 - 25% 2nd COAT BRUSH: 10% ROLLER: 10% SPRAY (with specific equipment): 15 - 25%. Apply from 0.18 to 0.25 litres of Sanaxil P-THERM per square metre of surface to be painted. Pail 4 l - Pail 14 l

Sanavel Breathable, natural, non-toxic, indoor paint, based on potassium silicate. Mineral-based, active formulation, high mildewcide and anti-condensation performance, prepared according to traditional recipes, for use in ecological building interventions, new buildings and in the restoration of vintage buildings and monuments. Sanavel consists of potassium silicate, natural pigments. It has very high breathability, remarkable mildewcide and antibacterial properties. It has no solvents, thinners, harmful substances and toxic emissions in general, and does not have thermoplastic effects. Restoring and decorative paint for interior environments. Application surfaces should be clean, free of soiling, crumbling and non-adhering parts, dust, etc. Pre-existing paints (washable, organic, solvent based etc. ) must be thoroughly removed. Preliminarily treat the support with the fixative Sanaxil Fix. Apply by brush, roller or spray. Sanavel is "dust-free" (it has started to be consistent to the touch) after about 1 hour. It can be overcoated after 4-5 hours, while it will be dry in-depth after 10-12 hours. Apply from 0.30 to 0.40 liters of Sanavel per square metre of surface to be painted. Pail 4 l - Pail 14 l

Sanastark Reactive solution of mineral silicates, capable of forming binding and stabilizing compounds for hardening and consolidating treatments by reaction with hydrated calcium salts and moisture present in masonry, plaster, stone and concrete. Indicated in the preliminary treatments to the subsequent plastering or smoothing operations, of plasters and powdery mortars and wall casings in general, in green building interventions and in the restoration of period and monumental buildings. Sanastark is a solution based on mineral silicates, demineralised water and natural dispersant. It does not contains traces of resins, solvents or thinners. The application of Sanastark does not affect the original wall breathability. Cortical reinforcement and elimination of pulverisation of mortars, plasters and masonry jointing. Also suitable as a natural fixative before applying lime putty- or potassium silicate-based plasters and paints. Remove the soilings and saline manifestations by vigorous brushing. Then eliminate the residual dust. Saturated with water until you reach the condition of "saturated with dry surface". Apply by spraying, proceeding from the bottom up: it can also be applied with a brush with natural long bristles. In the presence of pronounced degradations proceed with several applications, wet on wet. From 0.20 to 0.30 kg of Sanastark for each square metre of surface to be treated, based on the porosity of the support. Plastic can 5 kg - Plastic can 10 kg - Plastic can 25 kg

Sanalit Fiber-reinforced premix, based on hydraulic lime, light aggregates with high communicating porosity and cork flours, for the realization, with the sole addition of water, of screeds and lightweight substrates, with high thermal and acoustic insulation, in green building interventions and in restoration of period and monumental buildings. Sanalit screeds, packaged according to the specifications shown in this technical data sheet, are classified C5-F1-A22 in accordance with European standard EN 13813. For laying subbase screeds in high performance thermo-acoustic ecological buildings. Application surfaces should be clean, free of soiling, crumbling and non-adhering parts, dust, etc., conveniently saturated with water until they reach the condition "saturated with dry surface". Pour about 2/3 of the mixing water into the mixer. Gradually add Sanalit and the water still needed, by mixing until a homogeneous lump-free mixture of the desired consistency is obtained. Support the product at the reference height and float until a smooth and planar surface is obtained, preparing the joints beforehand where necessary. The mixing water indicatively necessary is equal to 65-75% by weight (8.5 -9.5 litres per 13 kg bag). Approximately 6 kg/m² of Sanalit for every centimetre of thickness to be implemented (approximately 600 kg per cubic metre). Bag 13 kg - Pallet: 50 x (Bag 13 kg)

Sanadek Breathable, natural, non-toxic paint, for internal use, diffusive type, based on long hardening lime putty, prefiltered. Mineral-based, active formulation, high natural anti-mildew and anti-condensation capacity, prepared according to the traditional recipes, for use in ecological building interventions and in the restoration of vintage buildings and monuments. Product based on lime putty and natural pigments. Sanadek has high breathability, it has remarkable mildewcide and antibacterial properties. It has no solvents, thinners, harmful substances in general. Decorative and interior renovation paint. The application supports will be free from fouling, powder, non-adhering parts, etc.; existing paints (washable, organic, solvent based etc.) must be removed. A preliminary fixative treatment of the surfaces is always advisable with a consolidating, transparent, Sanaxil Fix primer, based on potassium silicate. The application of Sanaxil Fix can be done by brush, roller or spray: the number of hands required and the dilution ratio with the most suitable water must be determined according to the conditions and absorption degradation of the supports. The admissible dilution range provides for water addition up to a maximum of 1:1 ratio. Apply by brush, roller, spray, in two coats, spaced-apart, one from the other, by about 24 hours. Apply from 0.30 to 0.40 liters of Sanadek per square metre of surface to be painted. Pail 4 l - Pail 14 l

Ringseal Pinza K4 Special dilating pliers with three noses, to facilitate the installation of the rectangular seals Ringseal L19 in a central position with respect to the metal blade caisson spacers for wood formwork. Expansion of elastic seals. Specific for the installation of the hydro-expansive rings Ringseal L19 on blade caisson spacers. Fully insert the nose of the pliers in the closed position in the slit of the rectangular gasket Ringseal L19. Press the handles of the pliers in order to dilate the seal. Install the dilated gasket at the centerline of the metal caisson blade. Release the pliers and pull them out of the seal. Product to buy as needed. Bulk material 1 unit

Repar Tix HG Bic Two-component thixotropic, structural, fibre reinforced cement mortar, with compensated shrinkage, with high intrinsic water tightness, and extraordinary physical and mechanical characteristics: adhesion, compression resistance, flexural strength, abrasion resistance, etc. Modified polymer mortar, with the addition of component B liquid, provided in canisters, containing special polymers in aqueous emulsion and hygrometric shrinkage reducers. Perfect for remediation of structural works and articles in degraded concrete and very high-performance coatings. After mixing the two components, Repar Tix HG Bic is perfectly workable with manual methods or with spraying machines. The applied and hardened material will have very high adhesion, durability, impermeable to water, with good vapor permeability, high physical-mechanical resistance (class R4 according to UNI EN 1504/3). The product contains migratory corrosion inhibitors in its B component. The thixotropic characteristics of the product allow excellent adhesion and easy spreadability on vertical surfaces, on the lower parts of beams, shelves or slabs, often even on structures indirectly subjected to light vibrations or dynamic stresses during application. It solves the problems of complex reconstructions or restorations, even on difficult-to-grip substrates and for a wide range of applied thicknesses: from a minimum of 3 mm (to be spread with a blade and finished with a trowel) to a maximum of 100 mm. and beyond, naturally in succession of layers of 25-30 mm / each. (for large thicknesses on large surfaces it is always advisable to provide a contrasting net on connectors fixed to the support). It does not require wetting or anti-evaporation protection after application. The superpozzolanic reaction of the peculiar reactive fillers contained in component A, the three-dimensional micro-armor provided by a balanced mix of READYMESH fibers, together with the special polymers and migratory corrosion inhibitors contained in component B, guarantee the hardened product very strong adhesion to the substrate, dimensional stability and maximum durability to environmental aggressions (from carbonation, acid rain, chlorides, sulphates). • Repairs and protective coatings of hydraulic works (pipes, dams, tunnels, etc.), offshore structures and artefacts in critical situations: chemical-physical aggressions, leaching water, marine atmosphere, etc.; • structural restoration of pillars, beams, floors and walls in reinforced concrete, including prefabricated ones, subject to high sulphate aggression; • volumetric reconstruction and bulking of concrete products with thicknesses from 1 to 4 cm, without the need for electro-welded mesh (the surfaces in this case must be appropriately hydroscarified with a roughness level > 7 on the ICRI _ International Concrete Repair Institute scale); • restoration of the cortical layer of the concrete and repair of the concrete cover detached following the oxidation of the reinforcing irons. Application surfaces should be clean, free of dirt, crumbling and non-adhering parts, dust etc., and saturated with water "saturated with dry surface". An adequate roughening of the surfaces by scarifying, sandblasting etc. is always necessary in order to obtain the maximum adhesion values to the substrate. The optimal values are obtained with high pressure hydro-scarification. Bare the irons undergoing disruptive oxidation or deeply oxidized, removing the rust of the exposed irons (by sandblasting or abrasive brushes). Pour component B (liquid) into a container (bucket or other) gradually adding and mixing component A (powder), continue mixing until total elimination of lumps. The optimal consistency of the product and the consequent physical-mechanical performances declared in this technical data sheet can be reached using 4.5 kg of COMPONENT B for each 25 kg bag. The excess quantity of COMPONENT B (0.5 kg) is particularly useful for priming the substrate, or for wetting the trowel in the final smoothing operation, or in hot and arid environmental conditions where the mixed product is kept at rest in the bucket it may require some light addition of liquid to regain its optimal consistency, thus avoiding uncontrolled water additions. Approximately 19,50 kg/m² of Repar Tix HG Bic for every centimetre of thickness to be implemented (approximately 1950 kg per cubic metre). Bag 25 kg [A] - Plastic can 5 kg [B] - Kit: 1 Bag 25 kg [A] + 1 Plastic can 5 kg [B]

Repar Tix GS A structural and shrinkage-compensated thixotropic cementitious mortar with a maximum aggregate grain size of 5 mm, consisting of high-strength cements, super-pozzolanic fillers, stabilising additives and high-tenacity polypropylene microfibres. The coarse grain of the aggregate and the excellent workability of the mortar render Repar Tix GS particularly suited to very thick volumetric structural restorations (with a depth of up to 50 mm per single coat applied) on reinforced concrete and masonry, even in environments with aggressive exposure (marine, industrial). It can be applied vertically or to the intrados of reinforced concrete structures, even of significant thickness, always in collaboration with the reinforcing rods, either manually or by spray, without the need for formwork and with wet curing for the first 48–72 hours. Repar Tix GS, the thixotropic structural mortar for significant thicknesses, can benefit from the addition of 0.25% of Fluid SRA, a special additive able to reduce both plastic and hydraulic shrinkage. Fluid SRA protects the curing of the mortar and, mixed with Repar Tix GS, can be considered as a technologically-advanced system able to reduce the rapid evaporation of water from mortar and promote the development of hydration reactions. Thanks to the interaction with certain cement components, Fluid SRA reduces final shrinkage by 20 to 50% compared with the standard values of Repar Tix GS prepared with the addition of water alone. For restorations, repairs, structural reclamations, reconstruction of concrete coverings, and the construction of reliable and durable coatings for construction, civil, hydraulic, industrial, concrete and masonry works in the event of extensive-thickness restorations. The applicative surfaces must be clean, free from contamination or any loose or detached parts, dust, and so on, suitably watered down until it is “saturated with a dry surface”. An adequate roughening of the surfaces by scarifying, sandblasting etc. is always necessary in order to obtain the maximum adhesion values to the substrate. The optimal values are obtained with high pressure hydro-scarification. Bare the irons undergoing disruptive oxidation or deeply oxidized, removing the rust of the exposed irons (by sandblasting or abrasive brushes). It is recommended to apply Consilex San consolidating realkalising agent to exposed surfaces in advance, prior to their restoration. Add two-thirds of the total mixing water (about 2.5 litres per bag) to the concrete mixer then gradually add the product and the remaining water until obtaining the desired mixture with a homogeneous consistency free from lumps. Ensure exposed surfaces are protected and wet-cured. Adding Bond HG to the mixing water (about 0.5-0.7 kg per bag of product) offers significant improvements in terms of adhesion, adherence, waterproofing, workability, malleability and deformation capacity. Approximately 19 kg/m² of Repar Tix GS for every centimetre of thickness to be implemented (approximately 1900 kg per cubic metre). Bag 25 kg - Pallet: 50 x (Bag 25 kg)

Repar Tix Bic Structural cementitious mortar, two-component, composite, with compensated shrinkage, fiber-reinforced, based on high-strength cements, super-pozzolanic fillers, water-dispersed polymeric resins, migratory corrosion inhibitors, anti-shrinkage additives, plasticizers, stabilizers and anticorrosion agents, selected aggregates, READYMESH microfibers in glass, with a high zirconium content, and multifilament polypropylene. After mixing the two components, Repar Tix Bic is perfectly workable with manual methods or with spraying machines. The applied and hardened material will have very high adhesion, durability, impermeable to water, with good vapor permeability, high physical-mechanical resistance (class R3 according to UNI EN 1504/3). The product also has a particularly low elastic modulus and contains migratory corrosion inhibitors in its B component. The thixotropic characteristics of the product allow excellent adhesion and easy spreadability on vertical surfaces, on the lower parts of beams, shelves or slabs, often even on structures indirectly subjected to light vibrations or dynamic stresses during application. It solves the problems of complex reconstructions or restorations, even on difficult-to-grip substrates and for a wide range of applied thicknesses: from a minimum of 3 mm (to be spread with a blade and finished with a trowel) to a maximum of 100 mm. and beyond, naturally in succession of layers of 25-30 mm / each. (for large thicknesses on large surfaces it is always advisable to provide a contrasting net on connectors fixed to the support). It does not require wetting or anti-evaporation protection after application. The superpozzolanic reaction of the peculiar reactive fillers contained in component A, the three-dimensional micro-armor provided by a balanced mix of READYMESH fibers, together with the special polymers and migratory corrosion inhibitors contained in component B, guarantee the hardened product very strong adhesion to the substrate, dimensional stability and maximum durability to environmental aggressions (from carbonation, acid rain, chlorides, sulphates). For any type of repair or restoration on deteriorated concrete and masonry. Restoration, structural recovery, reconstruction of the concrete cover, construction of reliable and durable coatings of civil, hydraulic, industrial, concrete and masonry building works, even in particularly aggressive exposure environments (XC2, XC3, XC4, XD1, XD2, XD3, XS2, XS3, XA1, XA2, XA3, XF2, XF4). Application surfaces should be clean, free of dirt, crumbling and non-adhering parts, dust etc., and saturated with water "saturated with dry surface".. An adequate roughening of the surfaces by scarifying, sandblasting etc. is always necessary in order to obtain the maximum adhesion values to the substrate. The optimal values are obtained with high pressure hydro-scarification. Uncover the irons undergoing disruptive oxidation or deeply oxidized, removing the rust of the exposed irons (by sandblasting or abrasive brushes). Pour component B (liquid) into a container (bucket or other), gradually add and mix in component A (powder), continue to mix until the mixture is totally lump-free. The optimal consistency of the product and the consequent physical-mechanical performances declared in this technical data sheet can be reached using 4.5 kg of COMPONENT B for each 25 kg bag. The excess quantity of COMPONENT B (0.5 kg) is particularly useful for priming the substrate, or for wetting the trowel in the final smoothing operation, or in hot and arid environmental conditions where the mixed product is kept at rest in the bucket it may require some light addition of liquid to regain its optimal consistency, thus avoiding uncontrolled water additions. Provide reconstruction thicknesses in the range 3 to 30 mm; for greater thicknesses add 3-6 mm gravel (add up to 30% by weight of the initial compound). High coating thicknesses, static monolithic requirements, etc., it may be necessary to resort to appropriate reinforcements (electrowelded mesh etc.) anchored to the support with Syntech Profix or GROUT MICROJ or Repar Tix G2. Approximately 20 kg/m² of Repar Tix Bic for every centimetre of thickness to be implemented (approximately 2000 kg per cubic metre). Bag 25 kg [A] - Plastic can 5 kg [B] - Kit: 1 Bag 25 kg [A] + 1 Plastic can 5 kg [B]

Repar Tix Structural, thixotropic, rheoplastic, composite cement mortar, based on high-resistance cements, superpozzolanic fillers, polymeric modifiers, anti-shrink agents, plasticisers, stabilisers, anti-corrosive, anti-allergic additives, selected aggregates, polypropylene fibres. Restorations and repairs, structural recovery, reinforcement reconstruction, construction of reliable and durable coatings for building, civil, hydraulic, industrial, concrete and masonry works. Application surfaces should be clean, free of dirt, crumbling and non-adhering parts, dust etc., and saturated with water "saturated with dry surface".. An adequate roughening of the surfaces by scarifying, sandblasting etc. is always necessary in order to obtain the maximum adhesion values to the substrate. The optimal values are obtained with high pressure hydro-scarification. Bare the irons undergoing disruptive oxidation or deeply oxidized, removing the rust of the exposed irons (by sandblasting or abrasive brushes). It is advisable to previously to apply the realkalising reinforcement Consilex San on the exposed surfaces, before they are restored. Pour 2/3 of the total mixing water(about 3 litres per bag) in the concrete mixer, gradually add the product and the remaining water, until a homogeneous lump-free mixture of the desired consistency is obtained. Cure the protection and the prolonged moist hardening of exposed surfaces. The addition of Bond HG to the mixing water (at a rate of approximately 0.5-0.7 kg for each lot of product) allows substantial improvements in terms of adherence, adhesion, watertightness, workability, moldability and capacity of deformation. Approximately 19 kg/m² of Repar Tix for every centimetre of thickness to be implemented (approximately 1900 kg per cubic metre). Bag 25 kg - Pallet: 50 x (Bag 25 kg)

Protech Sil Filler "Anti-crackling" basecoat based on siloxane water-thinnable resins, microfibre nylon, acrylic dispersions, fillers and specific additives, in a special highly water repellent mix ("lotus" effect). The special covering, filling (filler ) and vapour permeability capabilities, make it specific for renovating cracklings and small cracks, resulting from plastic and hygrometric shrinkage on existing plaster, before the next painting or coating with putty coat. The peculiar composition of Protech Sil Filler provides the performance of a real microporous filter, impervious to rain, it is exceptionally permeable to vapour: the "Sd" value is about ten times lower than that characteristic of normal acrylic paints. The product can then be applied on mineral media as well as on media treated with emulsion-based paints, providing a physical adhesion that is extremely permeable to vapour. Thanks to the physical structure of the binder, the silicone coating made with Protech Sil Filler, particularly resistant to light and weathering is even resistant to microorganisms. Renovation of vertical external façades characterised by significant presences of cracklings from shrinkage, also of width up to 1 mm. Regularisation of patches, of areas with different particle sizes and absorption. Particularly suitable for anti-cracking reclamation in buildings subject to protection as "cultural heritage". The support must be intact, dry and dust-free. Any biodeteriogenic settlements such as fungi, moulds, algae, lichens, etc. should be preliminarily tempered with specific products (CONSILEX ANTIMUFFA CLEANER and CONSILEX ANTIMUFFA). Where necessary it is necessary to provide suitable reinforcements with Sanastark. Static cracks exceeding 0.5 mm should be preliminarily filled with Fibrostuck. Apply at least 2 coats of Protech Sil Filler on the surfaces to be treated (about 125-150 g/m² per coat). It is recommended to "finish" the restoring treatment of the façade with the siloxane paint Protech Sil P. Apply from 0.35 to 0.60 kg of Protech Sil Filler per square metre of surface to be painted. Pail 25 kg

Protech Oxicrom Protech Oxicrom is an inorganic oxide/hydroxide based powder compound. Added in appropriate quantities and homogeneously distributed, it is ideal for the pigmentation of cement or similar conglomerates, plaster and paint. Protech Oxicrom oxides are available in yellow, red, brown, green, blue and black. Ferrous oxides have been used since ancient times for colouring paints. The main ferrous minerals from which the pigments are obtained are, of course, iron and its derivatives and compounds. The main colours of these pigments are dark gray/black in relation to ferrous oxide derivatives, and classic rusty red in relation to ferric oxide derivatives. Other more complex compounds may have colourings of yellow, orange, red and brown. Protech Oxicrom is ideal for the pigmentation of concrete for architectural and industrial floorings of washed gravel, shotcrete and exposed stone tiling, as well for the formulation of dyes and paints. The use of Protech Oxicrom ferrous oxide compounds is extremely simple: in the case of concrete, cements, mortars, plasters and so on, the pigment must be gradually and uniformly added to the mixer and mixed until a homogeneously coloured mixture is obtained. The indicative dosage of approximately 3-10% of the weight of the mixture to be pigmented should be varied according to the desired colour intensity. Add from 1 to 10% of Protech Oxicrom on the weight of the binder present in the mixture to the desired colour intensity. Bag 25 kg

Microsil 90 Grigio Selected grey silica fume for the production of high density and high performance conglomerates (waterproofness, chemical stability, mechanical strength etc.), for packaging sulphate-resistant, anti-leaching mortars, plasters, grouts and concretes. Microsil 90 Grigio consists of high purity (greater than 90%) silica fumes , selected, processed and bagged. Silica fume, the only component of Microsil 90 Grigio, is created spontaneously during the production of silicon steel (special and limited production). For all intents and purposes, therefore, silica fume is nothing more than particles of SiO₂ released during machining processes of silicon metal and iron-silicon alloys, in the form of very fine powder with vitreous structure (amorphous silica at 90-95%). These micro-granules, purified and selected, have a variable size between 0.01 and 1 μm, therefore much finer than cement granules, and are characterised by very high pozzolanic reactivity. Silica fume has been used now for over than 40 years all over the world for the fundamental improvement of rheological and performance characteristics of concretes, mortars and special plasters where they are introduced. Production of sulphate-resistant, sulphate-resistant, anti-leaching mortars, plasters, grouts and concretes , high performance in terms of watertightness, mechanical resistance, chemical resistance etc., in the realisation of civil engineering and hydraulic structures and works in marine, mountain, urban atmospheres etc. Microsil 90 Grigio must be poured into a concrete mixer subsequently to other solid components of the mixture: cement and aggregates. After mixing for about 30 - 45" add the mixing water, where possible with the addition of Fluid S, continue to mix until a strictly homogeneous mixture is obtained. Prepare test mixtures in order to determine the most suitable mix. From 10 to 30 kg of Microsil 90 Grigio for each cubic metre of concrete to be made. Bag 20 kg - Big bag 1000 kg - Pallet: 50 x (Bag 20 kg)

Grout Micro Fix The high-performance pourable micro-mortar Grout Micro Fix is a premix specifically intended for reinforced injection with the "sock" technique used for the consolidation of wall structures. Its particular composition has been designed to work in perfect coupling with the sealing sock and the threaded bars of the system, thus guaranteeing the main performance requirements required for this wall consolidation technique: easy mixing, high fluidity, injectability through the pipes injection even for long stretches, sufficient workability time, excellent mechanical performance even at short curing times. Grout Micro Fix achieves fluid and hyper-fluid workability even with very low water/cement ratios (< 0.4). thus resulting perfectly homogeneous, pourable, self-levelling and without water exudation phenomena. The very fine grain size of the aggregates allows the perfect filling of particularly narrow spaces and discontinuities (< 0.5 cm). The capillary absorption of the applied micromortar is very low, allowing great resistance to freeze-thaw cycles and washout. Grout Micro Fix achieves very high mechanical performance and is rich in microsilicas with pozzolanic activity and special additives which make it extremely durable even if positioned in particularly aggressive environments (due to chloride contamination in marine atmospheres). It is resistant to sulphate attack (Anstett test passed). The very fine binders, in combination with the special additives contained, allow Grout Micro Fix to develop exceptional values of adhesion to the steel and resistance to slipping of the bars with improved adhesion. When anchoring steel bars, the advantages of using Grout Micro Fix are: application also on damp supports (a situation that often limits the use of traditional structural resins); high resistance to high temperatures (for example in the event of impact and fire) thanks to the nature of the anchor. Reinforced injections for wall consolidation with the "sock" technique. Anchoring and fastening of bars with improved adhesion, threaded bars, recovery bars for integrative castings, tie rods, connectors (metal or GFRP). Filling of structural cracks on concrete and masonry with crack width > 5 mm. Drill the masonry with a diamond core drill (the diameter of the core varies from 50 to 80 mm depending on the diameter of the threaded bar to be inserted). Blow with compressed air and vacuum the dust from the hole. Mixing the micromortar Pour 2/3 of the total mixing water into the concrete mixer, gradually add the product and, subsequently, the remaining water, mixing until a homogeneous mixture of the desired consistency is obtained. Grout Micro Fix can be mixed with different consistencies, from plastic to self-levelling pourable. With 12-13% of water (3.0 – 3.25 lt/25 kg bag) plastic consistencies are obtained, with 13-14% (3.25-3.5 lt/25 kg bag) consistencies pourable, with 14-16% (3.5-4.0 lt/25 kg bag) self-levelling fluid consistencies. Small volume doughs can be mixed with a double/triple helicoid whisk equipped with a speed regulator. Install by injection or pouring within 60' 30' of packaging. If the temperature, at the time of application, is between 0 and 5°C, the development of mechanical resistance will be slower. It is recommended, with cold temperatures, to use lukewarm mixing water between 20 ÷ 30°C. If the temperature, at the time of application, is between 30 and 35°C, it is advisable to use low temperature mixing water (5 ÷ 10°C) and to apply the product during the least hot hours of the day (approximately morning or evening). Creation of the sock system Place the sock system inside the hole, making the injection tubes come out. Proceed with mixing the mortar and pumping through the injection pipe until it is completely filled. Use approximately 1,800 kg of Grout Micro Fix for each cubic liter of volume to be filled. Bag 25 kg - Pallet: 50 x (Bag 25 kg)